Microwave Capacitor Stun Gun / Experimental Hv Elephant Shock Gun - 4.7 ohm (current limiting and timing) k1 relay:. The video shows some experiments, like lighting up unpowered cfl bulbs from about 15 meters away and. If you liked the metal melter you saw in my previous project, here's how you can make your own! First, you will want to solder the red wire to the positive side of the battery. This increases the capacitance and reduces electrolyte damage. A long range stun dart gun.
The way i made my stunner was to get some of thoese green plastic (the ones in resin) caps, around 150v i think, them in parra (hehe i know i know). Editor electronic circuit published tuesday, august 30, 2016. The gun uses an explosive gas (butane) to launch a charged high voltage capacitor at a target. First, you will want to solder the red wire to the positive side of the battery. For example, if you had six capacitors at 650uf 400v each in parallel, your final capacitance and voltage would be 3900uf 400v.
Quad 2kv Capacitor Bank Deadly Taser Youtube from i.ytimg.com Here's a list of my components: When used, it can cause burns and/or serious muscle spasms. Rather than using volts, sabre measures the electric charge of their stun guns in microcoulombs, a metric used by the national institute for justice that provides a more accurate measure of stopping power. You can look, but don't touch! A capacitor bank for an emp should have capacitors linked together in parallel. 22uf >16v aluminum capacitor (mind the polarity) r1: You could build a beefed up stun gun and mount the output part on the end of a long stick. The capacitor in the boxing isn't functioning as the box was originally made for another project.
Attempt at your own risk!
You could build a beefed up stun gun and mount the output part on the end of a long stick. Before i get into how to built this device, let me warn you. The capacitor in the boxing isn't functioning as the box was originally made for another project. Attempt at your own risk! You can look, but don't touch! A microwave oven transformer, wired to arc continuously. The output of this electronic project is about 350v dc. To make the charge, find an old microwave oven and get the motor off the bottom, the one than moves you food around. The video shows some experiments, like lighting up unpowered cfl bulbs from about 15 meters away and. A capacitor bank for an emp should have capacitors linked together in parallel. The way i made my stunner was to get some of thoese green plastic (the ones in resin) caps, around 150v i think, them in parra (hehe i know i know). These arcs of plasma are lethal enough to kill on contact! 10x 1uf 250v ceramic capacitors in parallel.
This video is intended for entertainment purposes only. First, you will want to solder the red wire to the positive side of the battery. The way i made my stunner was to get some of thoese green plastic (the ones in resin) caps, around 150v i think, them in parra (hehe i know i know). You could build a beefed up stun gun and mount the output part on the end of a long stick. When used, it can cause burns and/or serious muscle spasms.
Homemade Taser High Output Power By Elohiem1 from i.ytimg.com This video is intended for entertainment purposes only. 22uf >16v aluminum capacitor (mind the polarity) r1: The voltage does not change, but the capacitance increases. I used to use a microwave oven transformer for groundhogs in my garden. First, you will want to solder the red wire to the positive side of the battery. This circuit is a cheap version stun gun circuit that is powered by two aa baterry. Buy sabre compact 1.6 µc stun gun flashlight — emits 1.6 powerful pain inducing microcoulombs, 120 lumen led flashlight with belt holster for quick access — rechargeable and strength independently tested: Here's a list of my components:
Stun guns are defensive tools used to stop an attacker.
The capacitor in the boxing isn't functioning as the box was originally made for another project. 10x 1uf 250v ceramic capacitors in parallel. I used a wire about three feet long strung between 2 pieces of pvc pipe stuck in the ground. You could build a beefed up stun gun and mount the output part on the end of a long stick. When used, it can cause burns and/or serious muscle spasms. The voltage does not change, but the capacitance increases. 4.7 ohm (current limiting and timing) k1 relay: A capacitor bank for an emp should have capacitors linked together in parallel. First, you will want to solder the red wire to the positive side of the battery. The way i made my stunner was to get some of thoese green plastic (the ones in resin) caps, around 150v i think, them in parra (hehe i know i know). The trigger automatically fills the combustion chamber with the correct amount of gas, then ignites it with the pulse transformer. This circuit is a cheap version stun gun circuit that is powered by two aa baterry. 22uf >16v aluminum capacitor (mind the polarity) r1:
When used, it can cause burns and/or serious muscle spasms. 22uf >16v aluminum capacitor (mind the polarity) r1: If you liked the metal melter you saw in my previous project, here's how you can make your own! This is for storing the charge. With the microwave oven transformer (m.o.t.) salvaged in a previous project, a simple electrical circuit can be rigged to get high voltage arcs to fly outward and upward along a v shaped spark gap.
High Voltage Generator Comparison 15kv 20kv 400kv 1000kv Youtube High Voltage Diy Electronics Comparison from i.pinimg.com 22uf >16v aluminum capacitor (mind the polarity) r1: Sabre's dual capacitor stun gun + flashlight looks like a traditional stun gun, but it has an led flashlight built in to the frame. The way i made my stunner was to get some of thoese green plastic (the ones in resin) caps, around 150v i think, them in parra (hehe i know i know). The capacitor in the boxing isn't functioning as the box was originally made for another project. To make the charge, find an old microwave oven and get the motor off the bottom, the one than moves you food around. These arcs of plasma are lethal enough to kill on contact! When used, it can cause burns and/or serious muscle spasms. Here's a list of my components:
You can look, but don't touch!
The way i made my stunner was to get some of thoese green plastic (the ones in resin) caps, around 150v i think, them in parra (hehe i know i know). This is for storing the charge. Editor electronic circuit published tuesday, august 30, 2016. To make the charge, find an old microwave oven and get the motor off the bottom, the one than moves you food around. C2 is made of 10x 1uf capacitors in parallel. When used, it can cause burns and/or serious muscle spasms. Buy sabre compact 1.6 µc stun gun flashlight — emits 1.6 powerful pain inducing microcoulombs, 120 lumen led flashlight with belt holster for quick access — rechargeable and strength independently tested: 4.7 ohm (current limiting and timing) k1 relay: 3v electronic stun gun circuit. The output of this electronic project is about 350v dc. The trigger automatically fills the combustion chamber with the correct amount of gas, then ignites it with the pulse transformer. Rather than using volts, sabre measures the electric charge of their stun guns in microcoulombs, a metric used by the national institute for justice that provides a more accurate measure of stopping power. With the microwave oven transformer (m.o.t.) salvaged in a previous project, a simple electrical circuit can be rigged to get high voltage arcs to fly outward and upward along a v shaped spark gap.
